We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all, I am using the nRF52832, Mesh sdk v4.2.0 and the nRF5 sdk v16.0.0. How to dynamically change the GAP name of device when using smart phone (nRF connect APP)to scan...
Hi, I'm following the steps on https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test.html
But in Programmer, the read, write, erase&write...
Creating a second advertising set with bt_le_ext_adv_create will generate an error -12.
Using nRF Connect SDK v1.8.0
The second advertising set is use for FOTA update...
Hi all,
i'am using nrf_Connect_sdk when i write this api
device_set_power_state(); it gives me undefined symbol
i enable CONFIG_TICKLESS_IDLE =y in prj.conf it gives...
Hello,
My company is evaluating the Thingy:91, we're interested in Multicell location lookups. My question is regarding the SDK, specifically if it's possible to configure...
Hi, I am unable to download my program and there's no detailed error messages, if any at all. Can someone please tell me what's going on?
Load "C:\\projects\...\\nrf52832_xxaa...
My company is creating a custom board using the 9160 and 52840. I have a BLE app running on a nrF52840 board that I want to port to the 52840 on the 9160 custom board. And...
I'm a newbie (few weeks) with nRF9160-DK and using nRF Connect SDK v1.7.1 / VS Code on a Windows 10 PC
Good afternoon,
I'm struggling with how to set up and start the...
Setup:
- nRF52832 , Softdevice s132, gcc
- iPhone is the peripheral. A custom service is implemented **on** the iPhone.
On the nRF:
- `#define NRF_SDH_BLE_VS_UUID_COUNT...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a function to connect to a central device, have the characteristic set...
Hi,
I am flashing Blinky led hex file on the flash at 0x5E000 location.
And again if i try to flash the different Blinky hex file at the same location. it wasn't working...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
