Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
I'm building a COAP client using the Nordic nRF9160DK cloud coap-client example code as my base. I have the UDP version working great. But I'd like to convert to TCP.. I was...
Hi all, I have an odd issue with an iphone XR. The NRF Connect for Mobile application can see adverts from the device when scanning, but the device does not appear in the...
Hey! I'm trying to sniff the data moving between a Bluetooth LE button and a Central.
Installation of the Bluetooth LE Sniffer went pretty smoothly but Wireshark only shows...
Hi,
I'm trying to use a nrf delay to make a delay for a motor. The idea is to make the motor oscillated by putting it forward and then reverse via a delay. (you can find...
Hello,
I need to run "west build" and "west flash" commands from my custom IDE/Editor. If I open up Toolchain Manager and then do "Open bash" or "Open Command Prompt", ...
Hello,
I am trying to do directed advertising while us ing the coded PHY whithout bonding the devices but i am running into some problems.
The device with the BT-address...
Hi,
I use nRF5340DK (0.11.0) as HCI controller and noticed it can randomly (?) accept PDUs with access address other than configured. This basically makes it impossible...
Hi,
When I build CLI sample in nRF_Connect_SDK, I don't get any USB port for CLI.
I believe the sample is in default mode built for UART.
How to build this for USB,...
Hello. I can't normally use USB for two-way communication.
The problem is sending the PRX payload in ACK packets.
After conducting a simple test: PPTX sends a packet once...
Trying to use the basic baremetal mode as my application is very simple and dont want to go through RTOS stuff.
I tried with Timer and RTC, both case if I enable the interrupt...
Dear Nordic Team,
I was trying to use the I2C peripheral on the nRF5340 with clock speed of 1MHz, but I kept getting the error "unsupported speed". I was using the function...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
I am using the nRF 52840dk board and I am new to nRF, I had worked on Cypress CYBLE & CYBT-343026-01. I am starting my development for basic BLE transmit, eventually, I am...
Dear Nordic experts, How do you verify that a (mesh) firmware has an app key assigned? What I'm looking for is basically the Mesh SDK's version of NCS's bt_mesh_app_key_exists...
I used the alternate method of installing nRF connect described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrf/gs_installing.html#build-environment...
