Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I have an nRF52840 + nRF5 SDK 17.1.0 project that has been running on S140 7.2.0 and we're getting ready to lock some things in. But we happened to notice that there is a...
Hi,
I use peripheral_hr sample code of V1.7.1 version to send Data HRM by Bluetooth. the frequency is 22 Hz only.
I would like to icrease sample rate to 2 KHz, could i...
Screenshot of error message
Hello, I've followed the steps required on YouTube for setting up VS code with nrf Connect for desktop and the toolchain manager. It didn't...
Hi Team!
Currently I an working on disabling JTAG/Debug and SWD lines to protect code from read/write through any JTAG debugger.
For this, I have used nrfjprog utility...
Hi Support team,
I am testing nRF5340+nRF21540 with MT8852B now. I come across two issues in running the DTM FW from nRF Connect SDK v1.8.0:
1. nRF21540 TX gain value...
hi， I'm working on passthrough firmware(nRF5_SDK_17.1.0_ddde560)，I need to increase the priority of the serial port,see following code,When APP_UART_FIFO_INIT priority set...
Hello, in my zephyr application, I have uart1 configured as receive only using uarte at 921600 baud rate. Below is the description node:
I have a device sending a uart...
Hi,
We are using nRF52810 on a custom board, and when creating that board in NCS (in VScode), the Kconfig options are limited. We are not able to enable/disable the DCDC...
I have a project using NCS v1.8.0 where I enabled openthread.
For some reason, when trying to build `mbedtls/library/ecjpake.c`, the make command uses `-DMBEDTLS_CONFIG_FILE...
Hi! Im doing a SPI transaction using EGU and PPI. Software triggers the EGU, and PPI_CHANNEL_1 uses this event to start the SPIM transaction and set the CS pin low. PPI_CHANNEL_2...
I have followed the procedures to create a DFU package
- Using existing sample hex file "hrs_application_s132.hex"
1. nrfutil keys generate private.pem
2. nrfutil pkg...
I am using SDK V1.8 and have noticed that RTT output will run for a short time then stop.
Debug is still running because breakpoints can be set, just no printk output or...
Hi, guys.
I have been using NRF Connect SDK 1.8.0 , I want to use this
"v1.8.0\zephyr\samples\application_development\out_of_tree_driver"
to develop my custom driver...
Hi,
I'm developing a miniature application on nrf52805. I got an nrf52-dk and I am trying to understand which SDK i should use.
So far my problem is that on one hand ...
I'm trying to transition from Embedded Studio to VS Code. I have a sample application that I created in VS Code that builds without error, but when I start the debugger I...
