Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hello, I'm experiencing an issue with talking to our mesh server after an IV update occurs. After a fresh provisioning the unit talks fine, however, one of our units has an...
I use nRF Connect for Desktop download the NCS v1.9.1, and i use SES open "C:\ncs\v1.9.1\nrf\samples\nrf9160\location" expample, but when i want build this solution or build...
Hello,
Are there any steps or documentation specific to nRF5340 to perform DFU over BLE and store the image into external flash and on the next boot it should get executed...
Hi guys,
As long as I know the Arduino Nano BLE 33 is built upon the nRF52840 microcontroller, so I am wondering now is it possible to use the source code from Nordic SDK...
Hi,
I am changing some code in the bootloader and would like to see some logs inside a specific function. The problem is that when I place the call for NRF_LOG_DEBUG() before...
Hi,
as am following below link for DFU-OTA . i was able to perform it. https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t...
Hello, this is a follow up on this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/84834/protecting-the-battery-via-sleep-mode
Our goal is to switch off the device ...
Hi,
I'm trying to understand which of the BT L2CAP modes are supported for a BT LE Controller. BT Core 5.3 supports these modes of operation:
Basic L2CAP Mode
Flow...
Hi.
Is it possible to add SPI or QSPI cleanup once mcuboot is done?
I've checked nrf_cleanup.c , but it seems that (Q)SPI is not turned off, which increases the power...
Hello,
I'm using nRF52833 MCU board for my project, I have to do power optimization to my project(Device).
In my device two sensors are there, and boost regulator and...
Hi, I have made a project that is based upon the aws_iot sample. The version of SDK and toolchain is 1.7.1. Now I have tried to upgrade to version 1.9.1. But then I get compile...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
I've written a sample eeprom application based on the eeprom included in the nRF52 SDK to test the EEPROM we use in a project. The application worked properly about 10 days...
Hello! We created our own model using SDK for Mesh and it works well. However, when testing in the "nRF Mesh" application using the "Vendor Model Control" field with the ...
When i use GPIOTE HITOLO(low accuracy）and then open spi to read flash and close the SPI（nrf_drv_spi_uninit） and close the SPI 's GPIO (nrf_gpio_cfg_default) .
The power...
