Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi, I'm developing an application using Libuartes to handle GPS data 1. According my knowledge about Libuartes, It will call the NRF_LIBUARTE_ASYNC_EVT_RX_DATA when the buffer...
Hi,
Since BLE advertising consumes current, I want to stop sampling ADC data during BLE is advertising. Are there any BLE events to know when advertising happens or are...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hello,
I've started to develop with the nRF Connect VSCode extension and enjoying it a lot. However, I've noticed when I share a project the build configuration doesn...
Hi,
I observed what appears to be the same issue as https://devzone.nordicsemi.com/f/nordic-q-a/51337/nrf9160-infinite-nrf_connect-blocking-behavior-post-lte-psm-wakeup...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
