Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello
I'm using nRF5340 DK with nRF Connect SDK 1.5.0 and SES IDE and I want to change the PHYs and TX power of the peripheral_uart sample ( v1.5.0\nrf\samples\bluetooth...
Hi,
Based on peripheral uart sample code on nRFConnect SDK 1.8, I'm developing a custom BLE application under nRF5340 using VSCODE though nrfConnect extension.
In order...
I tried to program this example developer.nordicsemi.com/.../README.html onto the nRF5340 network core, following the instruction from here devzone.nordicsemi.com/.../ncs...
Hi,
I am new here. I have a very basic question, maybe bordering on Dumb.. but couldn't see the answer in previous questions.
My board will normally be working on AC power...
Hello,
I'd like to remove the "configurations" in Segger Studio and the associated extra directory level; I consider them counter productive.
So how can I get rid of those...
Dear Sir.
A timer is defined for 1 hz,
Every 3 minutes or so we drive the buzzer with different pulses ( see code attached )
We are using the PWM to drive a buzzer...
error repported segger
39 minutes ago
Online lm
47 pts.
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I...
Hi team,
I'm streaming the sensor data through USB (using hterm) every 2.5ms.
i have configures USB as CDC and using virtual COM port.
In each iteration, i transfer...
i have nrf52832 using nrf sdk version_17 and s132.
I have application for logging
i have followed steps:
1). intially device in sleep mode
current: 0.35 micro Amp...
Hi,
I am working at a project that was abandoned by a guy that worked on my position. I have to fix some issues and add some features. I'm using SDK 17.0.2, my IDE is VSCodium...
Dear all,
I am now using two nrf52840DK and nrf connect sdk v1.7.1,and I want to send packet using llpm mode between two devices,one is receiver and the other is sender...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
Hi!
I am trying to develop a way for a Bluetooth Central and Bluetooth Peripheral using Secure Connections (security mode 1 level 2 if I'm not mistaken) using a static...
