Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have a product with an nRF9160 and using its modem to connect to a LWM2M server. I have recently enabled modem delta firmware updates, and have seen an annoying issue. The...
Hi,
We want to explore I2C examples in nCS SDK 1.7.1
Can you please enlist all the examples having I2C implementation.
also want to add I'm referring to I2C API's...
Hello everyone!
I am using my nrf9160dk to develop a system that connects to Azure IoT Hub. My firmware code is based on provided azure_iot_hub sample. According to azure_iot_hub...
I 'm using BLE Nordic UART Service (NUS) for streaming data packets which contains read sensor data. I need a way to check the packet loss happening for example if the other...
Hello,
I am developing an application that requires advertising of multiple custom service over BLE. I have successfully implemented the custom services, assigning a custom...
Hi All,
As far as I know , BLE Thrughput is basically set around a few parameters => 1. NRF_SDH_BLE_GAP_DATA_LENGTH
2. NRF_SDH_BLE_GATT_MAX_MTU_SIZE
3. NRF_SDH_BLE_GAP_EVENT_LENGTH...
1) I have set up the Zephyr development environment by following the instructions at https://docs.zephyrproject.org/latest/getting_started/index.html
2) I am able to build...
In my device， I must support HUB(central and peripheral roles) mode. I found it will drop data in weak signal. and It will be better when be central roles only in the same...
Hello.
I am just do one project with Zephyr and nrf52840 to control one step motor, the one task is to get pulse number of pwm pulse when motor is running , I think PPI...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
I start a application from the demo central-uart with the NRF CONNECT SDK 1.9.1
I try to communication via the com.
but the first byte of the rx buffer is wrong,I did...
I am running the throughput sample project on sdk 1.9.0 using two nRF5340 dev kits and am getting a throughput of 197 kbps using 2M PHY, Data Length 251 and Interval of 7...
Since upgrading to SDK 17.1.0 i get the following warnings of a redundant redeclaration for SystemCoreClock, SystemInit() and SystemCoreClockUpdate() for nrf52810 and nrf52840...
Hi,
I've installed the nRF Connect SDK, and want to bring up a command-line build environment.
I'm able to do it as it says in the instructions here : Bring up the Toolchain...
How to upgrade the nRF52832 tag in OpenWRT+nRF52832 gateway
gateway(openwrt+nrf52832) |_____ nrf52832 tag1 |_____ nrf52832 tag2 |_____ nrf52832 tag3 |_____ nrf52832 tag4...
