Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello everybody,
I am working on a nRF52832 DK and implemented libuarte (on a nRF52832) to communicate with another uC on said board. I am using sdk 17.0.2. The goal is...
Hi.
I want to write an app for nRF Connect for Desktop, where i keep track of the RSSI of a specific device and plot in into a chart. I thougt about reusing some parts of...
Hi,
I would like to use MCK as a clock for adc CLK 4Mhz.
Could i enable & configure all registers without I2S or PDM peripheral activation?
Is there a sample code for...
we have an app where we use a nRF52-DK board (with the 52832 chip) as a serial to BLE interface. We connect to the board using the USB UART channel. The interface IC on the...
In NCS@ sdk_nrf/subsys/bluetooth/gatt_dm.c: bt_gatt_dm_start():
if bt_gatt_discover() return with an error, the variable "dm" shall be release by calling "svc_attr_memory_release...
Hi,
I followed the structure of ble_app_uart__saadc_timer_driven__scan_mode project and customize a program on the nRF52805. I transmit data through BLE to Nordic uart service...
I get build error "undefined reference to `bt_mesh_sensor_apparent_energy32'" if I try to add this sensor type.
Rest of my sensors are included but this one not (e.g. bt_mesh_sensor_apparent_power...
I'm trying toa custom nRF52840 board using SDK 17.02 and SD 7.01
I create a read/Write only service, it shows up in nRF Connect just fine
I can write to the service using...
Good day,
1. I am running the Asset Tracker v2 app on my nRF9160DK and I am monitoring the battery voltage and its time stamp from my nRF9160DK, as this data is transmitted...
In the Matter documentation, under the topic Building Matter - > Getting Help , the "Also see the quick start guide" link is broken. For me it gives:
NOT_FOUND: Requested...
Hello,
I am trying to use googleapis.com to perform cell and wifi geolocation and am having trouble connecting.
I am using a custom board with a nRF9160 chip and the 1...
In the below picture, it says Thingy 91 is certified for the bands given below.
Can you please confirm if this board is certified for AT&T , Verizon?
Regards ...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
