Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I made a project based on the usbd_ble_uart_freertos example and added peer manager for secure connections.
It works in a way that someone can open the uart port...
hello,
i am using nrf52832 with lis3dh accelarometer and max30205 temperature sensor in our customised board with sdk 15.2 in my driver for temperature sensor i am using...
Hi,
I have developed an App to connect and communicate with a BLE peripheral. I used the nRF52840 device. Now I would like to change the firmware so that only my App can...
Hi, I am working with nrf9160, I want to convert INT64 timestamp value to CHAR array with sprintf. I use %lld but sprintf said only "ld" if I use %ld it convert only low side...
I have experimented with asset_tracker_v2 sample application using Cat Tracker sample in AWS. In addition I have created my own application which uses the same JITP certificate...
Hi, we have downloaded the latest nRFtoolbox for iOS from Github.
It compiles fine except it won't upload to our device or simulators.
We get this message:
The package...
Hi,
SDK: 14.2 Software device:332(5.0.0)
I want to use a bootloader to update my APP image. So I use DFU example and change some setting as below
/components/softdevice...
I have just installed VS Code and was following the videos for building an application. My board does not show up on the nRF Connect tab connected devices. The status bar...
I have been attempting to install nRF Connect SDK on macOS for several months without complete success. You can check my prior tickets for details. Nonetheless, I have recently...
Dear Members,
I can use a simple timer in :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fnrf_dev_simple_timer_example.html...
I use my customized antenna board (5 antennas on it) with the following IQ problem:
DF3 CTE[0]: samples count 45, cte type AOA, channel index 13, slot durations: 2 [us]...
HI
I am using nrf52840 and I want to merge nrf_calendar and app_ble_uart example, added ssd1306 oled 128x32 spi and mpu6050 as well,
but the error is from nrf_calendar...
which version of embedded segger studio do i have to download from the link ? www.segger.com/.../ ----> i am new for embedded-studio , so when i browse to the download page...
