Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hello!
I have used most of the GPIO pins on the nRF52DK, and most of them work. But I cannot get pin 21 to behave. I want to use it as an input. I have configured it as...
In nRF_SDK_For_Thread_and_Zigbee, on the nordic BSP package following three-button functionalities are available:
#define BSP_BUTTON_ACTION_PUSH (APP_BUTTON_PUSH) /**< Represents...
Hi,
I have 2 boards, one with monogoto esim and one with ibasis esim when I try with monogoto everything is working fine
when I try with ibasis esim i can't get registered...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
I am using 9160 to develop a customer's product, which needs to reduce power consumption as much as possible to prolong the battery life of the product. I know that 9160 communicates...
Hi,
We are using a self-developed python script to connect to nRF52840 in our products. The product contains many custom 128-bit services and characteristics (30+). These...
Hello,
I am working with a sensor that generates a simple crc8 XOR on based on this code from the nrf sdk 17 and sends it to a central:
I need to check this CRC8 on...
Hello Devzone,
While developing an nRF9160 based, battery powered device (working on the firmware piece of the puzzle) I have run into a couple of issues in my effort to...
Hello, I am looking into using zephyr with a host controller configuration on separate chips, where the controller is an nrf52832 chip. I was wondering how would the power...
Hello everyone,
I am developping on a nRF52840 using sdk-nrf v1.8.0 and Nordic MCUboot fork as bootloader.
For security matter, we want to use the HW keys MCUboot options...
HI,
I am developing a device that acts as both a peripheral and central device. This is working ok together, but I have one thing I cannot figure out. I separated central...
Hi Nordic Team,
Just following up with this post, I am not able to write anymore since the post is locked.
if I define 3 instances of fstorage, can I have 2 fds instance...
Hi,
We noted in the errata (Issue 133) that the radio performance is significantly degraded if the QSPI is enabled. The suggested workarounds are to 1) lower Vdd to 1.7...
