hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am developing Coap-Client and Coap-Server devices using nRf52840 dev kit. I am using ncs 1.7.1 sdk. I have a few questions.
1- I can successfully send a data received...
Hello all,
I have recently developed a custom board that uses an nrf52810. It also contains an accelerometer as well as some hardware for regulating the voltage and charging...
hi
I am using nRF5 Calendar example and
I have this problem
could you help me, how can I fix that?
I don't use the UART functions, I'm going to use SSD1306 to...
Hello!
I am currently working with Actinius' Icarus IoT board and I'm trying to get the interrupts to work. This is the boards' pin layout: At the moment I have connected...
Hi everyone,
I am trying to create a system to collect data from different sensors and store them in a FRAM. Then by using SPI, I want to transfer the data to the nRF52832...
Hi,
Trying to build the asset_tracker_v2 application I finally get the following error:
Rebuilding ‘zephyr / zephyr.elf’ from solution ‘build’ in configuration ‘Common...
Hi All,
I have problem running nRF5340 in continuous mode without any external trigger (timer/ppi). I would like to setup SAADC so that last conversion triggered new set...
Hello there, can I use the JTAG interface of the nrf52840 to perform a boundary scan of the components connected to it? I'd like to have fewer testpoints in my pcb and use...
I want to use CONFIG_UART_0_NRF_UART instead of CONFIG_UART_0_NRF_UARTE. But I don't get any option for this because CONFIG_UART_0_NRF_UARTE is selected by default .
I...
Hello everyone,
I am working on a project based on nRF Connect SDK v1.7.1 that I want to move to the new SDK v1.8.0. But I'm experiencing problems when building the project...
Hi We'll be adding to a design that uses libuarte/UART0. I've tested/run the example code and it's fine. Changing/swapping index from UARTE0 or 1 works fine as does reassigning...
Hi Sir/Miss,
I use SDK 17.0.2 version and softdevice s112 7.2.0 version to develop in nrf52810.
And, I base on this project (NUS with static passkey) which imports CTS_C...
Hi everyone, I'm developing a program with the NCS 1.8 using NRF52840 and I want to use the SPI, the fact is that I've to connect my device to those pins
And as you can...
