void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Dear Concern,
We are using NRF USB dongle in of our products. We are developing our android app in house. We want to add some security layer in the communication between...
I used 9160 to develop a project for the customer. During the project test, sometimes the data line or clock line level of I2C was abnormal due to hardware reasons. I wonder...
Hello, we have a thread that essentially is running a loop and we want that thread to be running for all the lifecycle of the app. If for whatever reason that thread died...
Hi Team,
I am using Open Thread networking protocols in my projects to communicate with the devices .I have seen while trying to changed some parameters over the network...
I am unable to do a FOTA with the SLM application on a nRF9160. When I try to do a FOTA with the command below, I get a 404 even though I know the URL exists (real host name...
Hello,
I have been working with custom nrf52832 board to develop firmware for my product. I have been trying to compile the example secure bootloader from the SDK v15.3...
Hello, I am developing a uart communication between the nrf52833 and the nrf9160. I found some examples but I don't want to use the HCI layer, I prefer to use the NUS service...
We have an application that wakes-up every N minutes and listen to devices in a ble mesh then performs many other actions. In order to save battery, we would like to power...
Hello
OS :- Linux
Hardware version :- BC805M
SW :- Segger embeded studio
I am using nrf52805. I am test it with ble_app_uart. It advertisement continuously and shown...
Hello,
I'm trying to transfer data to an L2CAP CoC on a nRF52832 from iOS and Android devices. I've configured the MTU and MPS so that the SDU fits in a single packet with...
I'm using BLE Mesh Sensor example that Client & Sever communication data each other.
Because I'm implementing one by one communication data that client > sever > client...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to add a custom UUID in the advertisement packet and scan for the custom UUID in the central device to...
Hi,
Our firmware currently only support full modem update, and I would like to perform a full modem firmware update from 1.2.0 to 1.2.7. According to the reply from https...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
