Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello I am implementing a battery voltage monitoring function using nrf52840. I am a beginner in hardware development. As the first step of this function, I am currently implementing...
Hi,
According to the Direction Finding White Paper , the CTE is a pure sin function at 2.4GHz. This is mixed with a local oscillator at 250KHz (for 1Mbps PHY) to obtain...
Hi,
I try to disable the reset mode and use the pin 0.18 as an normal input pin.
I'm using nrf52840 development kit (pca10056).
Does someone have i idea to resolve...
I currently have a nRF52832 DK connected to an external board with a BC832 module connected to the nRF52832 DK through a P19 connector. The voltage I have running and connections...
Hi everyone,
I'm currently trying to program my nRF52DK (nrf52382) to show it's battery voltage on the PuTTY emulator.
In order to run/simulate on the PuTTY emulator...
Hi,
I have working apps using custom BLE services on the 17.0 SDK
Now I need to write an app for the nRF5340 so the BLE softdevice can run in the network core
I have...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to conditionally switch the advertised UUID to another UUID. There is "sd_ble_uuid_vs_add...
Hello,
I have tested the USB HID Composite Example from Nordic SDK (15.0.0 and 17.1.0) on Windows and MacOS.
1) usbd_hid_composite_pca10056.hex from SDK15.0.0 works both...
I do not know how to use this site.
After my enquiry I received the following email and I am unable to reply to the answer.
> The ticket The input range of the SAADC...
I am trying to find where to implement secure communication between my BLE device (no display or input) and an Android tablet.
I am using the nRF_BLE library and am wondering...
Hi,
I've been browsing the forum here but didn't find an appropriate answer for my issue.
First, my platform & tools:
Programming nRF52833 (Laird BL653)
nRF5 SDK...
Hello,
I have been developing some products over the nRF51822 BLE. Got my introduction with nRF about 2 months back and despite the steep learning curve I was able to integrate...
Hi all. I'm using an old macbook and nRF Connect for Desktop just stuck at splash screen. Any version > 3.9.0 do not work.
System Version: macOS 10.13.6 (17G14042) Kernel...
Hello, I am using board nRF9160-dk (sdk 1.8.0). I need to get geolocation data using AGPS, for this I use the following sequence of AT commands:
AT%XSYSTEMMODE=1,0,1,0 AT...
