Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I'm trying to use nrf_delay_ms function inside rtc_handler.
I was wondering if using delay function stops rtc from counting up, so it disrupts rtc interval time.
Hi all,
I´m trying to test the LWM2M Client sample.
After following all the steps explained in this web , when I run it and connect to the DevKit via Putty, I get the...
Hi!
We are debugging low power in our custom board which has several chips (nrff52840, nrf9160, acc, fuelgauge, pmic, etc etc).
We are seeing strange random increases...
Hi,
I have managed to upload the asset tracker via mcuboot to my Actinius Icarus.
It should straight-up connect to the actinius.io cloud, but when I check the link monitor...
Hi, I am using an nRF52833dk and my project needs usage of Virtual EEPROM / emulated eeprom over flash memory. I could see that nCS-Zephyr provides a driver at the SDK "v1...
Hiii... Team,
I am developing a project based on the nRF52833 with the nRF5 SDK 17.0.2 and Soft Device S140
code is successfully built.. when i try to debug it showing...
my project need to recording audio data from codec continius for more than 10 senconds.i want use nrf5340 to do it.
the codec is tlv320aic3109 or wm8731.I have looked “easydma...
Hi,
I want to alloc dynamic stack memory for zephyr threads, such as k_aligned_alloc(stack_size, ARCH_STACK_PTR_ALIGN) instead of K_THREAD_STACK_DEFINE . I'm sure k_aligned_alloc...
Hello,
I'm building a system on nRF5340 which would support upgrading of CPUAPP and CPUNET applications. There is not enough space in internal flash to place all of these...
hello,experts,I use the NRF connect app on my phone,when I scan the devices ,I can get many BLE informations,I want to get the RSSI of each BLE with time .BUT I only need...
Hi all,
We are bringing up our custom board and we are having some trouble programming the modem firmware. Whenever we try to flash it using a JLink programmer and the Programming...
I'm using the nRF Connect app version 4.24.3 on an Android Tablet (Android version 10)
When I'm in the scanner tab and push the scanner button I get a graph of RSSI readings...
I use nRF Connect to debug some latency in logging data on my Android app.
On nRF Connect, the latency for the notification value (in the characteristic itself) is negligible...
I'm trying to find a simple way to log RSSI data vs time for multiple BLE devices simultaneously, and then put the data into a format which allow plots to be created in Microsoft...
