Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am in the process in getting the AWS version of the Asset Tracker v2 on my Thingy:91. I was having some issues with getting the cerificate but was able to get that...
I can not get the SPI Slave function working on nRF52840 (nrf52840dk_nrf52840 board). My goal is to have spi0 as master and spi1 as slave.
By linking the MISO en MOSI lines...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
I'm working on the 9160 SoC using nRF Connect SDK 1.8.0 to send MQTT messages to an AWS endpoint. The messages correctly are able to send and the device works for 5-10 minutes...
Using NordicSDK 1.6.1 and the following in the bt_le_adv_param and relevant settings in prj.conf
The secondary advertising data packet contains the advertiser address...
Hi all,
I am now using nrf52840DK and llpm example in nrf connect sdk 1.7.1.
Now I have three nrf52840DK, one as master ,and the others are slaves, they both use Latency...
Hello!
We are planning on using the nRF52832 DK together with an external antenna. We are highly interested in the readings being as accurate as possible, and we are wondering...
We are developing an application in which we need to modify an existing device driver. It's about LIS2DH driver that is part of nRF Connect SDK v1.8.0 and we are using VSCode...
Hi, we are using the nRF52 DK (nRF52832) to read data from the i2s bus and store it as a wave-file on the connected SD-Card. When pressing button 1 on the DK, recording starts...
(For some reason, I use "...' replace the original string) Here is the log for using AT to do HTTPS POST:
2022-02-07T12:19:39.057Z DEBUG modem >> AT#XHTTPCCON=1,"...",443...
Hi,
I'm working with NRF Connect SDK, and once in a while when I add new configuration options to the prj.conf, I get an error that some region overflowed by X bytes,...
Dear friend,
Since the customized nRF5340 board does not have an external 32.768KHz low-frequency crystal oscillator, the following is added to prj.conf in netboot:
The...
Hi
This is the first time I have tried to use the nrf52840 dongle and the programmer v2.3.1, it can see the dongle( com10), but as soon as I select Device tis is the response...
