Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi everybody,
I'm trying to make the nRF 52840 Dongle work with nRF Connect for Desktop v3.11.0 on Ubunutu 20.04 LTS.
I downloaded the latest version from here: https...
Hi to everybody.
I'm evaluating the possible options to perform self provisioning of nodes in a mesh network starting from the pb_remote client and server examples.
I...
Hello,
I have freshly switched to nordic and the surrounding nordic nRF Connect SDK from ESP due to a need for a low power chip with thread / matter.
I found some cheap...
Hi,
I have implemented the nRF5x-Custom-BLE-Service-Tutorial ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) using nRF5 SDK 17.1.0 on my nRF52...
Hello,
We've encountered an issue where if the ZED missed a network key update, it will not do trust center rejoin and continue to do secure rejoin Using nRF5 SDK for Thread...
Trying to west build -b nrf52840dongle_nrf52840 results in a qspi_nor flash error but the dongle hasn't defined any qspi_nor flash.
(This sample builds correctly with the...
Hi,
I want to output debug message(printk) through USB port on nrf52840 dongle. how to config it in zephyr, I have read the HelloWorld project code, but got nothing,
...
Hi,
I'm trying to make my nrf52840 dongle a ble central device. I did worked with the usbd_ble_uart example succesfully, but I was trying to add the ble_app_uart_c to it...
Isn't it supposed to autocomplete that? If I complete it to k_msleep(1000); the application builds and runs fine.
VS Code 1.67.2 nRF Connect for VS Code Extension Pack 2022...
Hi there,
We have a custom board that runs on a nRF52833 chip.
In order to flash firmware to that board, I use the Nordic DK (PCA10056), and connect my custom board to...
I've just installed the Nordic SDK version 17.1, SES version 6.3, and Segger J-Link Software version 7.64e on a new Ubuntu 22.04 laptop.
I've installed everything in their...
Hello everyone
I am using BLE Peripheral UART and Central UART samples to send data between two nrf5340 dev. kits.
I'm trying to set the directed advertising on the peripheral...
Hi All!
I am using nrf52820/33/40 devices. Able to connect central (1) and peripheral (4) concurrently.
Central is an end node(nrf52820) that is connected to the sensor...
