I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi,
I'm working with the ncs 1.7.0 peripheral_uart example and have observed faults when I send more than a few bytes at a time to the HW UART. (receive by HW UART for transmission...
Hello,
I am struggling trying to make this sample work on my board. I changed my prj.conf file with these lines:
And looking at other questions I discovered that sometimes...
Hi,
Is there any way to make app_usbd_audio_class_rx_start(...) complete the data transfer within the same context, rather than defer to user event
APP_USBD_AUDIO_USER_EVT_RX_DONE...
We have been using nrf connect installers 3.3.0 and now 3.7.0. We have recently seen issues with new users encountering this error when installing 3.7.0. Are there any solutions...
Hi,
I started to evaluate the Instaburst feature. I use light_switch_client example, but I am unable to provision the device once I enable this feature.
Below are the...
We are in the early phase of architecting a product that uses BLE and a proprietary RF protocol using the nRF52840 and are considering the addition of the nRF21540. In sifting...
I am currently trying to create a simple BLE observer which listens to advertisement broadcasts from a specific device (given via address). I attached the source code below...
Hi,
SDK - 17.1.0
I want to store my sensor data to the internal flash memory of nRF52810 for a long time. I have some questions here:
The data sheet says the flash...
Hello,
Few years ago I developed an application for nRF52832 (BMD-300). Now our customer wants to port the application to nRF52810 (BMD-330) as BMD-300 is not available...
When I'm trying to use arm_rfft_fast_init_f32 function from the CMSIS DSP library it seems to work with all sizes but 128. When the function is invoked with the size 128 it...
Hello,
Using a ZR device with nRF Connect 1.5.1.
I am wondering how to stop steering mode in a ZR device (e.g. if user requests an "abort").
It is started with bdb_start_top_level_commissioning...
Hi Dears:
When I downloaded and installed nRF Connect v3.3.1, the following screen appeared.
I remember when there was a drop-down box to select the BLE component. ...
Hi,
I would like to investigate some BLE issues on DFU project, but I couldn't find the implementation for advertising, connection and disconnection.
Where can I find...
Hello Nordic team!
I'm working on a BLE app with the nRF52-DK and an armband(M6) that has a heart rate sensor. My goal is to discover this service and read those values...
Dear ,
With nRF connect SDK, is there a way to check if the SD card is formatted with the correct file system, i.e. FATFS? If it's not in FATFS, how can we format it via...
