Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I have my programming environment set up to use the nRF Connect SDK through VS Code, as the most recent documentation suggests. I can successfully build and flash code...
Hi ,
How we can achieve the right and left align for the data buffer register for the nordic as well as zephyr ? any sample example where this option we can achieve.
Dear friend,
How much RAM does ECB encryption consume? Currently implemented using a third-party AES library (consumes 2.3k of RAM). Is there a way to encrypt that consumes...
Hi community,
I was changing the IDE from SES to VS Code and got everything running fine except debugging.
If i execute VS Code as administrator debugging works as supposed...
Hey guys,
i tried my best did my own research, but i can't get it to work.
I'm trying to manually add .c and .h files to a project in Segger Embedded Studio ialso put...
The following instructions are for using Segger Embedded Studio to flash the dongle.
https://devzone.nordicsemi.com/guides/short-range-guides/b/getting-started/posts/nrf52840...
Hi,
I have changed the vendor model for sending data from client to server in light switch example. Earlier it was just sending bool values. I have changed it to uint8_t...
Hi,
I try to write in flash with the flash_manager. I use this code to write in the flash.
Everything is fine when the flash writing succeed. But when a issue occur in...
Hi,
I'm using nRF9160 and want to use PWM with the automatic duty sequence feature using DMA, to make an LED "pulse" for example.
Looking at the documentation for the...
We recently bought a nRF9160 Eval board and are planning to connect it with a STM32H757XI_M7.
We would like to know, how well it can be integrated with the IwIP Stack...
Hi Nordic,
I am using the SDK 17, s140 and the nrf52840 , with a modified multilink NUS central example. The intention is to print over UART as fast as possible all data...
Hi All,
I have a nRF9160 custom board connected thru the P19 debug out connector to the NRF91DK board.
How do I 'make' the NRF91DK debug the custom board nRF9160 and not...
Hello. I have a custom board which contains S32K148 MCU and Murata MBN52832 BLE Module and several other modules like GPS, LTE etc. Board is powered via external 12 V adapter...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to know the handle value of the characteristic set as Generic Access and...
Hello,
We have a bunch of demo devices that were populated with the nrf5340 eng A version. So far we have been able to make them work by using nrf connect SDK v1.4.0 which...
