Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm testing a simple application based on the UDP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi,
My custom board using nRF52810, project was based on ble_app_uart_pca10040e_s112 and secure bootloader.
The size of application is 59k, and the bootloader is 32k....
Hi
I looked in the nRF9160_PS_v2.0.pdf，I can not find the voltage level of SPI signal pins，Does the voltage level of SPI signal pins equal to the voltage supply to the VDD_GPIO...
Hello,
I am using SES environment with nRF Connect SDK 1.9, SoftDevice S140 and nRF5_SDK_17.1.0 to clone the nrf52-ble-multi-link-multi-role example on Github ( https:/...
I'm facing some issues over connecting over to AWS with a custom board, the board was connecting before and the code connects with AWS using a Thingy91
Hi,
I'm trying to develop a simple application on the NRF5840 DK using the NRFConnect SDK inside VScode. I am struggling to see how to add external libraries to an application...
Hello,
I am using the nRF 52840 DK board. I am trying to implement the code for the HX711 in Zephyr.
I was just comparing the code with Arduino which I have written and...
Good Day.
I plan to use nrf52840 in my development, but at the moment this microcontroller is not on sale. But there is an nrf52840-Dongle on sale.
Can you please tell...
Hello,nrf_pwr_mgmt
I am doing basic BLE advertising on the nRF52840 DK board and using nRF5 SK 17.0.2. I can see the current consumption is ~50uA but after using nrf_pwr_mgmt...
So I have been wanting a opensource gaming mouse for a long time, and gwolves decided to make one recently using a nRF52840 (you can learn more here ). Only issue is that...
I built the project on VS CODE, but it failed at the beginning
log output:
> Executing task: nRF Connect: Generate config nrf52840dk_nrf52840 for f:\nordic-sdk\project...
Hi, I've made custom boards using nrf52840. In my application I did advertise forever with interval of 200ms. Now after several weeks of tests I've two boards out of seven...
Goodday
I thought I would try the webinar
️ nRF Connect for VS Code Webinar - Hackster.io
Im getting the following error after I add Build configuration
Building...
After installing NCS 1.9.0 Open Segger Embedded Studio does not show as an option any longer. I have tried to remove the SDK and install it again, but the result is the same...
Can distance be set between nRF52840 and APP? For example, set 5m and 10m through app. When the distance between nRF52840 and APP exceeds the set distance, app will remind...
