Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
Why nRF9160 example serial_lte_modem：http get data from http://hk.iotlib.cn/http_test_data.dat missing some bytes：
Repeat steps:
1. sdk:ncs v1.8.0 2.example...
SDK: NCS 1.8.0
Peripheral: nRF52832
Hello,
Is there a better example for creating a static library using NCS than the "external_lib" sample?
The example showcases...
I have a working build for the nRF5340 DK that implements a custom service and communicates over BLE. As I add features, the binary for the Application Core changes; the binary...
We have developed many solutions starting from example and modifying them to fit our needs, this one in particular has me stumped. We already have working BLE and USB CDC...
Hi,
I'm using nRF connect SDK 1.7.1 with ZephirOS.
I'd like to configure input / output to be redirected to UART and mirrored to USB CDC/ACM.
The reason is that I...
(nRF Connect SDK, v1.8.0, nRF52840)
I would like to create classic Bluetooth Classic peripheral behavior, the peripheral is not advertising (or advertising without name...
Hi, I created a Zephyr project for board : nRF5340DK_nRF5340_cpuapp . Now, I need to read the Device ID from FICR. I made changes in overlay file as shoen in atached first...
Hi,
I am using SDK 17.1.0 as a host scanner. When I changed the timeout to 0, there was a problem with the connection slave (NRF_ERROR_INVALID_PARAM). I'm pretty sure the...
I'm currently using: - NCS 1.6.1 - Zephyr - NRF52840
I'm using the lwm2m client to read and write to lwm2m objects.
When the device starts for the first time, I store...
Hi,
I downloaded the hello_world_with_mcuboot.zip file that Simon provided in one of the ticket few days ago - Case ID: 283917.
I built hello_world_with_mcuboot project...
Hello,
I would like to know if the application / use case stated below is implementable.
In my application I would like an nrf52840 to communicate with the Bluetooth module...
hi,
In the NUS routine, it is necessary to turn off the peripherals before entering the idle mode to minimize the power consumption, but there is no change after adding...
Hi,
I'm trying the sample fat_fs on the nRF5340 DK
1) It does build, but there is awarning
CMake Warning at D:\nRfConnect\v1.8.0\zephyr\CMakeLists.txt:722 (message)...
On a MCU PCA10040 v2.0.0, I ran the command:
.\nrfjprog.exe -f NRF52 --program .\final_image.hex --verify --reset
Which subsequently caused the board to go into a reset...
