Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Firstly, I have the following definitions in sdk_config.h and when declaring the qwr buffers:
Note that in the above, the intention is that TR_SLU_CONFIG_MAX_LENGTH could...
Hello,
Working on a zigbee end device with a number of endpoints that are all behaving nicely in general but wondering what the zigbee-ish way of allowing for user config...
Hi,
When I build ble_app_uart->PCA10040->S132->arm_no_packs in SDK17.0.2,there logging an error: #5: cannot open source input file "system_nrf52_approtect.h": No such file...
Hello! nRF Connect for Desktop is a desktop executable program provided by the manufacturer, which contains the function of ble. Now I want to extract the functions of ble...
In SDK v17.1.0, In QSPI init, I see all the pins are configured as Input pins during nrfx_qspi_init. Isn't this wrong? Shouldn't we set the SCLK, CSN, MOSI pins as O/P pins...
Hi! We're considering switching between the mentioned packages, both in nRF52833.
I've looked around dev zone and product specificaiton pages, and could not find anything...
Our device connects to a cell tower and then creates a socket to our gateway. I monitor +CEREG to see what it goes through to connect to a cell tower. Below is the meaning...
I testing UART0 data transmossion. But, could resolve why CPU resets when executing : if (!nrfx_is_in_ram(buf)) in uart_nrfx_uarte.c file. See atached image, where Reset occurs...
I am developing a custom board with an electronic paper device (EPD) attached, which will be controlled with SPI and a five additional GPIOs (a mixture of inputs and outputs...
Hi Guys,
I have a nRF5340-DK(PCA10095) here and I'm planned to perform some BT-SIG RF testing with it but I can't find the proper hex file for DTM(Direct test mode) setup...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
