I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello everybody,
I am working on a nRF52832 DK and implemented libuarte (on a nRF52832) to communicate with another uC on said board. I am using sdk 17.0.2. The goal is...
Hi.
I want to write an app for nRF Connect for Desktop, where i keep track of the RSSI of a specific device and plot in into a chart. I thougt about reusing some parts of...
Hi,
I would like to use MCK as a clock for adc CLK 4Mhz.
Could i enable & configure all registers without I2S or PDM peripheral activation?
Is there a sample code for...
we have an app where we use a nRF52-DK board (with the 52832 chip) as a serial to BLE interface. We connect to the board using the USB UART channel. The interface IC on the...
In NCS@ sdk_nrf/subsys/bluetooth/gatt_dm.c: bt_gatt_dm_start():
if bt_gatt_discover() return with an error, the variable "dm" shall be release by calling "svc_attr_memory_release...
Hi,
I followed the structure of ble_app_uart__saadc_timer_driven__scan_mode project and customize a program on the nRF52805. I transmit data through BLE to Nordic uart service...
I get build error "undefined reference to `bt_mesh_sensor_apparent_energy32'" if I try to add this sensor type.
Rest of my sensors are included but this one not (e.g. bt_mesh_sensor_apparent_power...
I'm trying toa custom nRF52840 board using SDK 17.02 and SD 7.01
I create a read/Write only service, it shows up in nRF Connect just fine
I can write to the service using...
Good day,
1. I am running the Asset Tracker v2 app on my nRF9160DK and I am monitoring the battery voltage and its time stamp from my nRF9160DK, as this data is transmitted...
In the Matter documentation, under the topic Building Matter - > Getting Help , the "Also see the quick start guide" link is broken. For me it gives:
NOT_FOUND: Requested...
Hello,
I am trying to use googleapis.com to perform cell and wifi geolocation and am having trouble connecting.
I am using a custom board with a nRF9160 chip and the 1...
In the below picture, it says Thingy 91 is certified for the bands given below.
Can you please confirm if this board is certified for AT&T , Verizon?
Regards ...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
