Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Our application requires switching between NB-IoT and LTE-M without flashing firmware of any part, including modem. We were recommended the nRF9160/nRF52840 due to this capability...
I'm referring to the sample code : ncs \ v1.9.1 \ nrf \ samples \ bluetooth \ peripheral_uart
I'm not happy at all with the samples, the documentation is quite poor in many...
What do I have to set in order to require a new passkey every time I connect with my nrf52dk_nrf52832 build?
I have tried to prevent bonding using bt_set_bondable ( false...
I am using the PPK2 kit to perform current measurements of our system and what I notice is that after a couple of minutes the program becomes very sluggish.
When I open...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi, We are using nRF9160 on our custom board. (SDK 1.9.1) with "serial lte modem" firmware. We have two external antennas for GPS and LTE. Now we are implementing location...
Hi
I want to communicate with nRF52BK (nRF52832) board via its UART.
Eventual goal: Get Android device, acting as USB host, to connect with nRF52DK board's UART Short...
i devzone
I following the blog ( devzone.nordicsemi.com/.../testing-max-range-with-ble-with-nrf21540dks-and-nrf52840-dks) to setup 20DB on 21540 DK (pca10112), it is works...
Hi,
I was trying to turn off logging in zephyr\subsys\usb\class\cdc_acm.c, by setting LOG_LEVEL to 0, but when I do that the logs are still printed on the console.
First...
I added custom module to default asset_tracker_v2 to upload custom data to AZURE_IOT_HUBuisng nRF9160DK kit. All the functions are working well. The default is getting transferred...
The iBASIS SIM card I received with the Thingy:91, during activation, I got an error message that the SIM card is expired. I contacted the iBASIS support and I got a new SIM...
Hi everyone,
I'm currently doing some experiments with the zigbee feature of NRF52840 and I'm working with an PCA10056 development board.
The light_bulb example however...
Hi,
I'm so confused about UART error when I enabled DFU and download bootloader.
In my application, UART worked normally when disabled DFU, but logging ERROR 1 after enabled...
The provision button in nRF Mesh is no longer active. It worked yesterday but I think there was a update to the app and it no longer works.
The app finds the unprovisioned...
Hello all,
Four leds are connected to the GPIO (22-25) and gpio are defined and with a simple method within the while loop I can see them working
Next is to use the...
