Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
There are several questions regarding this, most recent I could find from 6 months ago ( https://devzone.nordicsemi.com/f/nordic-q-a/81686/is-there-support-for-gatt-caching...
Hi,
I would like to know if I can update the firmware of modem from 1.1.1 to 1.3.1 on Thingy91 (hardware version 1.4.0).
My goal is to use AGPS and PGPS assistance services...
The product specification states that "o nly the dedicated QSPI pins shall be used. " Is this a recommendation or a requirement? I would like to configure a different pin...
I accidentally closed the original ticket , so I create a new one.
Hi,
recently I'm building dfu function on my board, using nrf51822 qfaa and softdevice s110.
...
hello,
Im using nrf52840 Im trying to emulate a chip select signal for spi slave with gpiote and ppi. I used an active high signal as an event and a signal(cs) that is toggled...
Hi everyone,
I have some questions regarding RSSI:
1. Is there any Bluetooth reference that evaluates the RSSI? For example what RSSI range is considered as perfect, moderate...
env:
SDK: nRF5_SDK_17.0.2_d674dde
KEIL- ARM
SoftDevice： s140_nrf52_7.2.0_softdevice
i can't understand how MBR jump to bootloader, and how MBR konw the start address...
I'm using SDK 17.0.2 and I'm trying to write a small central device. It should connect to a single peripheral and exchange some data.
Once the peripheral is found, central...
Hi,
I am trying to get access to the code 1.99.99-dev1 branch of the NCS, but I'm not sure where I can find this. More specifically, I would like to use the code of the...
Hi.
I am developing a small notification monitor.
It used a 150mha battery and a 0.92 oled.
I want it to be connected to my phone via Bluetooth and when I send a string...
Hello DevZone,
I have a project where I want to use NFCT for communicating and charging. I have used the NRFX_NFCT library to read and write to my transmitter because...
Hi,
I am doing the java programming with BLE advertise, and I want to make BLE advertise events stop when the advertising events number enough. Are there any methods to...
Hello,
for a device I'm developing I need to be able to set values from an App as well as from the device itself (buttons on said device). So far everything works fine...
