Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
Hi,
I am working NRF DK (NRF52840), when I am trying to flash the program in NRFGOSTUDIO from that it was showing some error that is " No device detected, or readback protection...
Hi, All
I am using VS Code and nRF connect v1.9.1, I try to set some parameters for scan etc. during running. It would be ideal if they can be saved into NVM and loaded...
Hi,
I am conducting a mesh test and it contains:
An android smartphone,
- running nrf mesh 3.1.7 on github
- sending hundreds of bytes packets to the mesh nodes...
Hi,
I am completely new with the development kit nRF5340, I have plugged in the USB and turn it ON, the status after that as follows,
- LED5 is blinking continuesly
...
Hi I have been doing some current consumption measurements using Nordic's Power Profile Kit 2.
The device I am measuring is a custom BLE device that uses the ADC to sample...
Hello, I'm having problems to debug my application when I check the "Enable debug options" in the build configuration. If I don't check this box, I can debug, however, most...
Hello,
I'm working with a little project in NCS 1.9.1, chip is NRF52805 acting as central, connecting to a peripheral that requires passkey and L3 security. Everything works...
Hello,
We are developping based on SDK 15.2 for nRF52 using IAR 8.11 and S132 V6.1.0 as softdevice for central/peripheral application. Bellow is the test scenario explained...
Hello,
I have an application where I send the data I receive over UART, directly to a phone connected with BLE. However, the BLE connection is often not fast enough to send...
I am using nRF52840, SDK16.0.0, Keil v5.18a to developing application. When I changed heap size in Keil C/C++ option, it failed! It can be successful if you change heap size...
Mr Jared, I am sorry. I accidentally pressed the verify button and the ticket(Case ID: 288462) was closed.
To answer your earlier question.
I checked the nrf_drv_rtc_cc_set...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo,
As I am developing a new product (peripheral acceleration sensor device) I would like to update the DIS service data with the following characteristics, Manufacturer...
