I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
Hello. We are preparing production. So I have to provide flash tool as well as binary only to factory without develop...
Hi there,
We are trying to enable the interrupts on one of the UARTE peripherals, and are having trouble finding the interrupt number within nrf5340_application.h? It is...
Hi Everyone,
The custom device I am working on is a BLE peripheral device and uses softdevice S132,
therefore to get accurate triggering of ADC sampling and to avoid periodic...
Dears,
We are MCU Programmer Supplier, now we are developing the off-Line Programmer for NRF5340, and encounter some problem as below:
1. Does the Nrf5340 Flash Memory...
I have a custom model server that sends 8 bytes of data
I set up 2 nodes - one to publish to an address 0xC002, one to subscribe to publication
Provisioning and publish...
Is there any documentation/tutorials for using NRFX drivers directly in Zephyr without trying to create conforming device drivers? I have a lot of code written for the NRF52840...
We have a board based on the nrf9160dk.
The project is essentially based off the "LTE sensor gateway" project with hcl_lpuart to utilize the nrf52840 for BLE. Chip shortages...
Hello,
I am performing garbage collection. During the garbage collection an event could be fired (from the softdevice) that causes updating of records.
My question is...
Hi
I would like to know, if Zephyr-s ssd16xx driver supports display driver board power supply control? I see from Zephyr documentation ( solomon,ssd16xxfb (on spi bus)...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
