Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
For my Thingy91 project I need to hook into a variety of hardware interfaces including I2C. I am struggling to relate the pins https://infocenter.nordicsemi.com/topic/ug_thingy91...
Hello,
I'm using the nRF Connect SDK 1.9.1 and I have defined a custom board with nRF52840. This works for normal code (samples, etc).
The .dst has the following structure...
Hi,
Im using PCA10056 nrf52840 to measure light intensity with photodetector.
I got that sensor to measure the intensity of the light on the Arduino. But I don't know...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
We got a project that is using custom boards and custom libraries that is able to compile for one board and that output strange errors for an other. Following is the prj.conf...
Summary: Not able to see messages from printf() statements in the code on the serial monitor.
I'm new to Nordic platform and to Segger Embedded Studio.
I have a Nordic...
Hello,
could you please tell me how to configure the Hardware Chip Select Funtionality for SPIM3. I am developing a communication between a sensor and the NRF via SPI transfers...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
