Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hi,
I am working on BLE on nRF52833dvk, am able to execute the sample example . I have one of the requirement, that I need to write the unit test cases for Bluetooth for...
Hi
I would like to use power management module with CAF. I got it somehow working and the device is going to poweroff or standby mode and wakes up, if i push some button...
Hi all
I'm developing a BLE application using nRF52832 : SDK 17.xx
My SW is based on the project ble_app_gls as I need to use a PASSKEY
I experience 2 difficulties ...
Hi
I am positing this here - although maybe that is cheeky of me, as the issue I am having is with an Android app, which I want to use to communicate with a Nordic device...
Hi,
1. Can nRF9160 equipment automatically identify the following two networks?
2.CAT-NB1/NB2
3.CAT-M1
4. Automatically identifies the NB network when inserting a...
Hi,
I have a weird issue occuring when trying to connect to my MQTT server.
If i run the code on a NRF9160 DK i can connect perfectly fine to my MQTT server calling...
Hi all,
In the nRF9160 https_Client sample, I was able to connect to the server by provisioning a server-matched root certificate to the nRF9160.
Can I connect to an...
I've been playing around with the v1.9.1\zephyr\samples\boards\nrf\system_off\ example code, as I want to implement something similar in my own code. But I want to be able...
Hi
I would like to change my coded PHY layer 1MBps to 2Mbps.
For that, i just change the params BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_2MBPS in my code.
But now the function...
Hi,
We are battling to get to the advertised low power values as described here:
https://devzone.nordicsemi.com/guides/cellular-iot-guides/b/hardware-design/posts/measuring...
Hi
I'm trying to create a central device to connect with a series of different peripheral devices. All the peripheral devices can be discovered during the scanning. However...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hi,
I have previously compiled the zigbee command_line_agent for the PCA10059 which I use for testing.
It worked when uploaded so I have one working PCA10059.
Recently...
Hi,
I have a problem getting interrupts by the rtc component working. I am using the nrf58211 chip, nRF Connect SDK v. 1.9, uBlox BMD360-eval development board.
My code...
