Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello, I am trying to read data from the sensor using I2C, I have the nrf9160 on an Icarus board https://www.actinius.com/icarus .
I tried following this guide: https:/...
Hi Nordic Team,
I see that I am supposed to GND 2 of the SPI lines and drive the CSN high to use it in GPIO control only mode. We wanted to TP out the SPI bus for the FEM...
I am trying to send value 0x75 using I2c but when i check the value using logical analyzer i found it 0x74. and when i tried to send 0x77 i found it equal to 0x76. any help...
I am currently working on a project in which I want to transmit audio wirelessly from one nRF chip to another. Currently I am using the nRF Dongle to act as the transmitter...
Hello Everyone,
I am using NRF52833 in my project and I have implemented one service named borrower. The code details are in the attached in the files. When I open nrfconnect...
Hi Nordic,
I have 2 nrf52840 hosts running gazell HOST mode, and 1 device running gazell DEVICE mode. My question is, when device sends data to host, will both 2 hosts receive...
I connected to the cloud with the factory installed fimrware ( thingy91_1.4.0_production_final, mfw_nrf9160_1.1.1).
In the "Firmware Updta History" it shows: "To use the...
Hi,
I'm working on optimizing the download time of data via bluetooth with the nrf52820 android and IOS phones. To do this, I chose to play with the connection parameters...
Hi,
I am using a j-link EDU to program our devices. I use nRFConnect 3.11.0 and prorammer 2.3.3. My problem is that I don't get the j-link device up in the programmer tool...
We want to be able to manually send Friendship requests from LPN or to change request interval runtime.
It was possible to send requests manually using nRF5 Mesh SDK, however...
Hello,
I am testing out a custom board with the nRF52840 and I am trying to interface with an I2C slave using the chip. Right now I am just trying to see if I can find the...
Hello,
I was not able to see the device in select device drop down box in nRFconnect programmer app. My aim is to program BLE soft device into the DK.
OS: Windows...
Dear Forum,
I have successfully compiled and pretested the direct test mode firmware for SDK_17.0.2.
The UART is shown as /dev/ttyUSB0 in my Ubuntu 20.4 Linux system....
