I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
Hi,
Since BLE advertising consumes current, I want to stop sampling ADC data during BLE is advertising. Are there any BLE events to know when advertising happens or are...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
Hi everyone,
I am looking the schematic of nRF52840 (PCA10056) and I am a bit confused with the Power Sources (sheet 7 of 7).
There are three load switches that prioritize...
Hello,
My project:
- I have a low consumption project width BLE. - I'm using internal LF clock (I know it's better to use an external) - I use the Beacon example project...
Hello!
I am working on a FOTA solution for the nRF52DK, I have followed this example: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
Hello,
I've started to develop with the nRF Connect VSCode extension and enjoying it a lot. However, I've noticed when I share a project the build configuration doesn...
Hi,
I observed what appears to be the same issue as https://devzone.nordicsemi.com/f/nordic-q-a/51337/nrf9160-infinite-nrf_connect-blocking-behavior-post-lte-psm-wakeup...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
