I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
hi, i am using a cutom board based on nrf5340 mcu , so, while setting it up i am facing the problem in checking logs and led status.
i am uisng the nrf5340dk board to build...
I have shell working with the following configuration
CONFIG_SHELL =y
CONFIG_SHELL_BACKENDS =y
CONFIG_SHELL_BACKEND_SERIAL =y #also selects serial
CONFIG_SHELL_CMDS...
I downloaded a project in named prj9160 from Github. The prj9160 had three folders : Azure, firmwre, mscerts. I run successfuly the following command :
west build -p always...
Hi everyone,
I want to run nrf_drv_saadc_sample in a loop but I do not want to use PPI and TIMER peripherals because they increases the power consumption of my device. I...
Hi , am working on mesh example from v1.8.0\nrf\samples\bluetooth\mesh\light_switch. In this example they are using generic on/off server , light LC server and other server...
Hi.
For example, for the nRF52832 BLE chip, could it, in some manner, be only visible/communicate with a specific/particular smartphone app? How? using the MAC?
Regards...
Hello, I have a nrf5340dk communicating with nrf52840 dongle connected to a pc with UART baud rate of 2M. Connection parameters are:
7.5ms Conn interval
1ms Slave latency...
Background The adxl362 driver native to the zephyr kernel doesn't support FIFO operations, so I built my own out-of-tree driver that relies on a new accelerometer API instead...
I wish to add a firmware version to my project. Because we are hoping to use OTA for updating I have set the configuration paramater:
CONFIG_MCUBOOT_IMAGE_VERSION
in proj...
After working with arduino's and microprocessors like the ESP8266 and ESP32, I recently started toying around with a nRF52840 dev kit. After going through some tutorials,...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
Hi, I have a problem configuring the PPP Modem correctly and I'm not quite sure what i'm missing here.
I'm running the code on a custom board. We are using nRF52832 to talk...
Hello dear!
1- What is the relation(formulas) between current in uplink I uplink and the data packet size?
2- What is the relation between the iDRX PDCCH repetitions ...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
Hello. I am setting up the nrf9160dk and when I got to the step when I had to activate the SIM card. When I had to fill up my address etc. it didn't let me save it so I was...
Dear Sirs,
I have a sensor working as a peripheral and using the Nordic NUS service. I have a poblem discovering the two MSBits of the sensor's address when it connects...
