1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
Firstly, I have the following definitions in sdk_config.h and when declaring the qwr buffers:
Note that in the above, the intention is that TR_SLU_CONFIG_MAX_LENGTH could...
Hello,
Working on a zigbee end device with a number of endpoints that are all behaving nicely in general but wondering what the zigbee-ish way of allowing for user config...
Hi,
When I build ble_app_uart->PCA10040->S132->arm_no_packs in SDK17.0.2,there logging an error: #5: cannot open source input file "system_nrf52_approtect.h": No such file...
Hello! nRF Connect for Desktop is a desktop executable program provided by the manufacturer, which contains the function of ble. Now I want to extract the functions of ble...
In SDK v17.1.0, In QSPI init, I see all the pins are configured as Input pins during nrfx_qspi_init. Isn't this wrong? Shouldn't we set the SCLK, CSN, MOSI pins as O/P pins...
Hi! We're considering switching between the mentioned packages, both in nRF52833.
I've looked around dev zone and product specificaiton pages, and could not find anything...
Our device connects to a cell tower and then creates a socket to our gateway. I monitor +CEREG to see what it goes through to connect to a cell tower. Below is the meaning...
I testing UART0 data transmossion. But, could resolve why CPU resets when executing : if (!nrfx_is_in_ram(buf)) in uart_nrfx_uarte.c file. See atached image, where Reset occurs...
I am developing a custom board with an electronic paper device (EPD) attached, which will be controlled with SPI and a five additional GPIOs (a mixture of inputs and outputs...
Hi Guys,
I have a nRF5340-DK(PCA10095) here and I'm planned to perform some BT-SIG RF testing with it but I can't find the proper hex file for DTM(Direct test mode) setup...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
