1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
I'm interested in zephyr to make the image file lighter. Have a any solution to update for BT DFU with signle bank? I wonder I can use single bank like Nordic Softdevice.
Hello,
I am aware that this is not an Arduino support forum, but if I'm not violating any rules, I'd like to ask a question in hope that someone might have provide a helpful...
I'm developing on an iMac M1.
Over 2 month I tried to get the nRF Connect for desktop (V3.9.3) running on my M1-mac, without success.
Toolchain manager (v0.10.3) works...
Hi Nordic Team,
Currently we are exploring nRF52840 DK.
We have observed BLE Enable SOC usually have two cores, one as an application and one as BLE Soft Device core....
Hi - I am using the /nrf/samples/matter/lock sample as a reference template to develop my own app. Thank you for providing it!
I am able to build and flash the basic build...
After updating the firmware on NRF9160 Connect DK (using mfw_nrf9160_1.3.1.zip as well as the ltem asset tracker hex file) LED 3 does not turn on and AT commands in LTE Link...
I am using a mac M1, running macOS 12.0.1 Monterey.
J-Link Software and Documentation Pack v7.62 (latest)
NRF Connect for Desktop v3.10.0 (latest)
Programmer v2.3.1...
Hello,
i'm using a nrf52832 dk and i'm using the example ble app uart.
I saw the packets that are send for rx or tx but with packets of 20 bytes
I saw this post, https...
Hi,
I have some problem with NRF52840. When I use software example "ram_retention" in peripheral directory on 2 différents board I have 2 differents state of VBUS pin. ...
Hello,
I am relatively new to iOS development and have now made the iOS version of the nRF Toolbox from the Github. After some initial difficulties, I was able to get the...
Hi,
I have a peripheral device that running on nrf5340 and can be updated via MCUMGR SMP. i tested it via Device Manager application and it is working.
My question is...
I'm building a custom board based on nRF52840.
I'm providing 5V input via USB to VDDH & USB pins. The default output of the first internal regulator during high voltage...
Hi, before buying the PCA10056 kit, I have some questions about the USB CDC ACM example.
I'm new to the USB CDC ACM.
At the Infocenter , it says that
This example...
Hello everyone!
I have just got started working with Nordic devices, in particular the nRF9160. I have been doing tests using the provided UDP sample from nRF Connect SDK...
I tried building and running the buttonless DFU example project. However I get the following UART output:
It seems like it can download the softdevice by itself if the memory...
