Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Let me start by saying we have not ruled out other possible sources of errors at this point. However, right now all the evidence is pointing to an issue with the nRF52840...
I attended the Introduction to the nRF21540 RF FEM for range extension webinar and bought a few nRF21540-DB kits
The first thing I want to do is compare the range increase...
Hi,
We have our own MQTT broker setup with TLS running on a AWS EC2 cloud service. I am building my code based on the MQTT_SIMPLE example. I have only a CA certificate in...
In my project I use nRF52832 embedded in MuRata module. I have a BLE service with capabilities very similar to NUS service.
I've managed to add support for LESC + SEC_MITM...
I am attempting to upgrade from nRF Connect SDK version 1.7 to version 1.9.1
My application is using the nrf52840 on a custom board.
I'm using Zephyr and created a board...
Hi,
currently I'm testing several options to transfer data in broadcast manner, i.e. in fact extended advertising due to the amount of data to transmit. A few days ago,...
Hallo,
I am starting to develop an application using nrf5340 SoC. I have got two Audio DK and would like to begin my development using nRF Connect SDK.
However, I was...
Hi,
With the nRF5340 DK boards (PCA10095), there are 3 VCOM ports (as viewed in VS Code) - printk debug logs for the app core are transmitted on VCOM2. However, the nRF5340...
I was trying to schedule a work item when a struct k_poll_signal is raised by an interrupt, but was unable to get the work to happen. I could tell that the k_work_poll_submit...
Hi, I'm new to this and I was just wondering, since I'm still learning and successfully coded my first app, I'm asking how can you flash / burn / build & run SMD component...
yes, i meet a problem.i notice that isp have done a AOA demo based on Nordic board.
but i use it to get the angle.i find i can't use it.what is this problem?
I am running a nrf52dk_nrf52832 build with SDK v1.9.1. A week ago I was building my project and everything was working fine. Then, my program stopped being flashed - I could...
Hello!
I'm working with nRF9160 on a custom board and I'm trying to use SUPL to improve time to first fix, I'm following the sample nrf9160/gnss/src/assistance_supl.c. I...
I am testing the Asset_tracker_v2 application on thingy-91. I took the SIM card out so the device goes into the boot loop.
The on_state_init () function has the condition...
