I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
I am not sure what I am missing in this. This is a custom board so there is no other circuitry on this pin other than a pad to monitor the signal changes with.
When...
Hello!
Regarding the CRC on the nrf52840 the specifications make it clear that the maximum length of the CRC is 3 bytes, We are working on an industrial communication protocol...
Hi
How can I readout the actual timer value on the fly? I use the timer in capture compare mode and like to read out the timer value.
nrfx_timer_clear(&m_pyq5848_timer...
Hi all,
I have set up an nrf52840 as the sniffer to sniff the connections between my custom board and central phone. My goal is to figure out the bottle neck of the ble...
I based my project on the secure wireless uart example in the nrf5 SDK and linked to the precompiled gcc library 802_15_4_lib_gcc.a
I then tried to add multiple entries...
It seems that once we install nRF Connect into VS Code it completely takes over and now when I open any file in VS Code I see all of the nRF connect tabs and controls which...
I'm trying to debug an application however there is no documentation on how to set up the debug.
How come nRF connect is selecting the HEX file. I want it to select the...
Hey,
I am trying to use the Jam Detection Feature of Openthread on my nrf52840 DK. The device is running as coap server with the example code
"simple coap server". I...
Hi,
Is there any tutorials or examples avaialble for adding DFU service? I would like to add DFU service for my application. I am using nRF52840 development board with...
Hi All,
I'm using SDK17.1.0 and I have a question about pairing.
I have a project that references the ble_app_bps program, but I don't get pairing notifications when...
Hi All,
I have a question, it seems to be the SES debugger crashed.
My project only uses peripheral devices, my purpose is to combine libuarte with my framework.
And...
I want to send an interrupt instruction from appcore to netcore by using IPC.
Implementation code in appcore:
Implementation code in netcore:
However, in actual...
I have a vendor mesh model that needs to send a custom 8 byte message.
Here are some definitions
BT_MESH_MODEL_PUB_DEFINE (vnd_pub, NULL , 3 + 8 ); <--what is with this...
Hi,
I have a nRF52840 Dongle connected up to an external j-link debugger. I have been using this over the past few weeks with no issues and unfortunately I have managed...
