I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I'm trying to make a server/client communication with a lwm2m server and DTLS authentification.
In the first place, I used Pre Shared Key that i provided with the modem...
Hi,
I have a nrf5340dk configured as a NUS peripheral, it collects some sensor data, packs it into a 138 byte buffer and sends it to the central.
On the central side...
Hello,
I want to compare the RTC's counter_get_value() ticks with the internal clocks k_uptime_ticks() ticks. The problem is when the RTC is connected with our nrf 52840...
Hello,
While programming my board with a merged.hex I sometimes see some differences at the end of the Programmer log.
Sometimes the log ends like this,
2022-03-25T14...
Hello guys,
I am having problems on addressing an issue with my firmware. Maybe someone can assist me to find out the root cause for this, because I don't understand too...
Hello,
We buy nRF52832 chips and use them integrated on our own PCBs.
Our devices are small BLE devices to which your phone, computer, anything can connect to.
They...
Hi，
Would you provide the software of NRF52832 ESB communication with NRF24L01 ? And share the two Demo Boards PN for NRF52832 and NRF24L01. Plan to buy the DEMOs.
...
i study in derection of DOA.I now can get the iq sample from my Putty in COM PORT.i use NCS 1.9.1.I build and flash in my two boards with nrf52833.i use the cammand line tool...
Hi,
We came close to occupying all available flash memory in the nRF52833 board:
Memory region Used Size Region Size %age Used FLASH: 185620 B 187904 B 98.78% SRAM:...
I use the zephyr version 3.0.9,when i build the hci_rpmsg project,it have serial error.then i chnange the onfigruation by add some new definition.
I add some configurations...
Hello,
I have some issues with activating the gps-module for the "second-time" through mqtt.
See uart logging below.
First GPS attempt works, socket is created successfully...
Hi,
I have been trying to follow the guidance here: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf53-designs
I'm using a custom...
Hi,
I was thinking of buying a Power Profiler II, but was wondering if it is possible for the profiler to measure the consumption of the chip itself or does it measure...
Controller- MDBT40 (nrf51822 based)
Softdevice - S110
I have an application where data comes from UART and have to send over BLE simultaneously. When I initialize the...
