I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi there,
I have a problem to implement the SPIM in the Network core. I cannot detect any signal from SPI_SCK & SPI_MOSI by oscilloscope and logic analyzer (no signal from...
Hi,
I'm using VS Code to develop an application based on the Zephyr iso_broadcast sample.
How do you edit prj.conf? If I select prj.conf in the Explorer pane, then click...
Does the nRF52840 support Bluetooth low energy power control? I am using raspberry pi, running Raspian, kernel version 5.15.30 and I am specifically referring to the product...
Hi support team:
I develop my project with sdk 15.2.0 on nrf52832. Now I met a situation that I might need to call app_timer_start() again before the same timer is timeout...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
Hi! I'm trying to understand how my board is working. I think that the Arm Trustzoned provides the possibility to the board to have two domains, one secure and one non-secure...
Hello,
NCS1.9.1, two nRF21540DK, Windows10 X64, VS Code,
periodic_adv and periodic_sync , only 3M distance can recv data,
if over 3m, will unstable reception / disordered...
Hi,
I am on nrfConnect SDK v1.7.0, with a nrf52832, with UART in ASYNC mode.
During the uart event callback, the event type UART_RX_STOPPED, but when I check for the error...
Hi,
Hello,
I am working on TM4C129XNZAD microcontroller, from that everything working fine like no error no warning and If I flash the code also its programming and the...
I've mostly gotten the tools installed to build for the SparkFun Thing+ nRF9160 board. It had a version of the at_client installed, in that it responded to some AT commands...
Hi
I am testing POF function on 52832 based on SDK14.2 and SDK17.0. And test project is SDK example ble_app_beacon.
Code as show:
#include "nrf_drv_power.h" static void...
Hello all,
I'm currently working on an evaluation of a AoA location system. For that I'm making use of the Nordivc 12 Array Antenna, and two nRF52833 DK (one connected to...
Hi, I'm facing an weird problem when I use an function that is contain while loop
When I uncommented the 35th line => call GPS_init_usingWhile(GPS_RMC,RMC_response); ...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
