Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
i am compiling sample code for accelerometer from sample C:\Users\mohit\nrf\v1.9.1\zephyr\samples\sensor\adxl362 .
i don't make any changes in code . when i try to build...
Hi,
I am debugging an Application running on a custom board that uses the NORDIC nrf52832 processor connected to an IMU over twi. I am using SDK17.0.2
I find WDT is kicking...
Hello Nordic Team,
I've been having good success with the 52840 and been slowly migrating a lot of my projects to the chip. While I await modules to arrive from a supplier...
I'm trying to use 9-bit UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_DATA_BITS_8...
Hello,
NCS1.9.1, nRF52840DK, Windows10 X64, VS Code,
1.
i want to read voltage from RT_ADC pin (P0.04),
and than converting NTC thermistor value to Temperature.
...
Hi,
My setup include a nRF52840-DK board that has an ESP32 WiFi module connected to it via UART. The idea is to source the new firmware from a server located in the cloud...
Hi, I'm doing experiments with Bluetooth direction finding. I am using the example of the nRF52833 development board, and I have obtained the IQ representation of CTE and...
Hi I am using the aws_iot example on the nrf9160 DK.
I have opened the zephyr.dts file and in the section uart0: it has the following
I've reached this point trying...
Hi,
I am looking to connect the ds18b20 sensor to the nrf9160dk. I followed this post, but when I tried running it, I was getting a "create_nordic_project.py failed (1)...
2022-04-12
Hello Devzone Community,
I have a couple questions regarding availability of nRF9160 LTE modem settings PSM and eDRX. Question (1) If my local celular carrier...
Hi Nordic Support,
I'm running into an issue with ncs v1.8.0 directing log and shell to RTT backend.
Objective: Using nRF NCS / nRF52840dk - I want to dedicate 1x UART...
Hi,
I have opened a ticket with Kenneth and verified it by mistake. It is now locked. I have done the changes Kenneth asked me but it didn't resolve my problem.
thanks...
Hi,
I am connecting my nrf9160 based system to the nRF Cloud and sending data from it.
I got the cloud to show the RSRP values that I sent it through the following JSON...
