Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I did respond to this:
https://devzone.nordicsemi.com/f/nordic-q-a/86426/peripheral-and-central-uart-sample-crash-when-sending-longer-messages
I do not see a update...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
Hi
We are working on an algorithm applicable to the indoor positioning of ships. We want to improve the algorithm further on top of the existing algorithm for Bluetooth...
I'm on a Comcast cable modem connection. When I've tried to pull up this site over the past few days, I've gotten "The page cannot be displayed because an internal server...
Dear nRF DevZone,
I have question regarding Zephyr k_sleep() function and NRF52840 timers.
I am developing an application for nRF52840 SOC and for that I am using nRF...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to pair from "Settings"-> "Bluetooth" of iOS (iPhone 12 Pro). For pairing...
Hello,
I am developing an application that requires use of some of the traditional C "stdio.h" functionality. My current development setup is the nRF5340 DK running Zephyr...
I'm using sdk for mesh version 5.0.0, sdk version 17.0.2 and my board is nrf52840-DK.
How can i keep mesh config after wake up from deep sleep( system off).Plus, when my...
Hi,
This morning when I tried to access devzone, it says I have been IP banned. I have the same issue as this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/86922...
Currently running NCS 1.7.1, SUPL client 0.7.0 and MFW 1.3.0 it has stopped connecting properly from the last time I've played with it:
Not sure what's up there..
...
I am having trouble powering my uicc. I feel like I am just looking for some setting, but I have not found the right one yet and I am at a loss at this point.
What I have...
I used direction finding rx/tx examples(get 45 points of IQ data). I used the ref period IQ data (8 points) can caculate base phase and the phase velocity(setting is 500KHz...
