Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hello,
We observed that the BLE-Mesh provision logs are happening in FCBs of NV Flash, For my application i need them to be logged on RAM. Kindly suggest how I can achieve...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
