Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
1. Please provide the COMP input voltage precision in CROSS event on VIN+ and VIN- crossing mode
2. When the input voltage changes to the minimum, the output terminal...
Hi everyone,
i would like to ask if there is available an example project for the nRF9160DK that uses aws_iot through a NBIOT modem configuration.
I took the aws_iot sample...
Hi,
I am trying to connect my LSM9DS1 with nrf52840, this is Arduino nano 33 BLE board. I already figured out that i had to enable it and enable TWI bus. After some readings...
I am trying to change the curvetype of the ecdh example from NIST secp256r1 to Curve25519 or Koblitz secp256k1.
To achieve this I enabeled Koblitz curve secp256k1 and Curve25519...
Hello Devzone,
Our research group is using the NRF52832 chip embedded in a flexible substrate to transmit EMG (muscle) signals via Bluetooth. We’ve been having a couple...
I have been trying to find a solution for this but to no avail. I have nrf connect 3.10 installed. I am trying to flash my compiled code but keep getting the error: Unsupported...
In general, it's not a question, but the only suggestion for SDK developers how to improve debugging way.
So, while implementing DFU upgrade in my project I faced to the...
Hello everybody,
My project is based ble_app_eddystone example and nRF5_SDK_17.2.0 SOC is nRF52832.
Beacon advertise Eddystone UID +Eddystone TLM +Eddystone URL, works...
Dear,
how to change the adv. timeout setting and disable uart0 and uart1 in ncs v1.6.1?
I use the nRF5340 and example peripheral_lbs.
The path is as below:
nrf\samples...
I am using the following CAF modules on nRF52840DK, ncs 1.9.1: Buttons, LEDs and Power manager (see attached project caf.zip)
Button 1 is used for ON/OFF fuctionality. When...
I submitted a project idea for the Electromaker make it smart thingy:91 contest. Part of that was to detect and alert a user if there was an impact. This would require access...
Hi,
When using RTT for debugging on the nRF5340, after every flash i have to press the following button:
Then every time i get presented with the following dialog...
How do I find out which peripherals are available at the same time?
Somewhere it was mentioned, that peripherals wit the same "ID" are on the same HW and only one of them...
Hi,
What's the max range achieved with BL5340 (With PCB Trace antenna) in indoors and Outdoors when advertising and connected mode? (With 1M,2M and Coded PHY(125Kbps,...
