Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hello,
I have a running thread network now. Yay!
I am using a BMD-341 module from a old board as a Thread Sleeping end device. Getting great results.
I've flashed the...
Hello, we have made 50 cards with your microcontroller,out of the 50 cards there are 6 cards which consume about 10µA in sleep, while the others consume less than 1µA. Have...
Hi All,
We are using NRF52832 for our project.
We are using LED driver based on I2C protocol.
Do we have example code for I2C driver?
Please send some example/sample...
Hello,
I've installed nRF Connect for Desktop for Mac and from the UI using the Toolchain Manager I've installed nRF Connect SDK v1.8.0. After installing the extensions...
Hi,
I have been developing an application that reads sensor data (over SAADC and SPI) over an interval, serializes the data, and transmits the data over BLE_NUS to a companion...
Hi Nordic,
when I enable the Bluetooth configuration, the sensor trigger stop to work. when I comment the Bluetooth configuration, the sensor trigger back to work.
I recorded...
hi support team,
for nrf5 sdk ble_app_hid_mouse example, this example shows how to use swift pairing, it works. but I have one question for it, after I press reset button...
Hi, I'm trying to run samples provided by Nordic but I fail. My problem is west can not find my Jlink.
I can flash the chip (nrf52840 custom board) using nrfjprog
...
1. When I run the SDK routine provided by the official, ble_app_uart program, the circuit board acts as the peripheral , the protocol stack is pre-downloaded to the board...
Hi,
Update MDK to handle APPROTECT, MDK can be downloaded from MDK website, but no details on hot to update MDK to nRF5 SDK. Any guide lines to update the MDK with nRF5...
Hi, I am new with nRF microcontrollers. I created a custom board that mounts the nRF52840 microcontroller. I made a firmware that uses BLE to exchange data and everything...
Hi,
I'm using nRF Connect SDK v1.7.1 with two nrf5430 DK. My goal is to evaluate the different security levels. For testing i send messages with the Nordic Uart service...
According to the AT command reference v1.7, the nRF9160 SIP modem firmware v1.3.1 added the %PERIODICSEARCHCONF command.
It does though not mention anything about the behavior...
We are evaluating OpenThread for a custom board with a BL654 from Laird, which contains an nRF52840. When running the OpenThread CLI sample from nRF Connect SDK 1.7.1 we are...
remoteproc_mgr_config() from nrf5340_cpunet_reset.c that is called during init by zephyr for starting main thread uses hardcoded pin numbers for uart with cts/rts pins and...
