I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising, that's why I use the periodic_adv example coming with...
Hello,
I am using the vl53l5cx TOF sensor and implementing the ULD using zephyr. My setup is a bl654 board using zephyr on sdk 1.9.1. However I am running into an issue...
(replica as the previous post was archived by accident...)
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M....
Hello,
first of all i am a new user of NRF microcontrolers and embedded systems. I ve been searching on this forum for a simple PDM microphone example and although there...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
Hello,
I want to test the throughput of Isochronous Channel using ncs sample code "iso_connected_benchmark". So far I can successfully build the code and run in central...
Hi,
I'm trying to save system uptime when the watchdog callback occurs.
The NVS functionality works when calling nvs_write elsewhere in code.
Calling nvs_write inside...
Other Configurations:
prj.conf
# General config
CONFIG_LOG = y
CONFIG_LOG_DEFAULT_LEVEL = 4
CONFIG_STACK_SENTINEL = y
CONFIG_NEWLIB_LIBC = y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
