I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
Hello there,
I am using the rtc2 in NRF52832 to interrupt at randomly generated time instances. Now, I am trying to integrate this functionality in a framework that uses...
I would like to use the low power pwm library to get a breathing LED effect on my device. The MCU I am using is a BMD 350 and the LED is connected to nRF52 port P0.02.
...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
Hello!
I am trying to install MCUMgr on MACos.
I install the Go Programming Language and then follow this: https://docs.zephyrproject.org/latest/services/device_mgmt/mcumgr...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
Hello, I would like to make a follower robot. For this, I wanted to use the AoA to locate my phone and thus determine the direction in which the robot should go.
I'm really...
Hello,
I am working with a nRF5340 and need to use both CDC and mass storage on SD Card. I started my application based on the CDC example and it has worked fine.
Now...
Hello,
NCS1.9.1, VSCode, nRF52840,
from link UART Driver – Nordic Developer Academy (nordicsemi.com)
uart can't to receive data continuously,
receiving evt->data.rx...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
