Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
I'm developing two products that will communicate via ble_uart. Both products have battery, so I need to reduce consumption as much as possible. I'm currently using nrf52832...
Hello,
Im getting different behavior on my SoC depending on what power source I use. For example I tend to get alot of retranmissions from client to server if I have them...
Hi,
I have taken nrf_connect_sdk_v1.9.1 and build n=my application over it.
When I delete .git file from v1.9.1/zephyr/.git, then my west compilation don't occur.
...
I tried to open a program created by else one. The Output is shown below. I could not understand: Due to which warning abort ? There are many warnings.
Creating solution...
Hello Devzone Community,
My name is Ted, and I am continuing my effort to configure a Zephyr based, Nordic aws_iot sample app based firmware to run and support nRF9160 lowest...
Hey I am using a nrf9160dk and I am trying to get lte-ble to work I get the above assert failed.
Does anyone have an idea how to fix this?
I have the hci_luart file...
Hello,
My group has developed a board using the nRF52840 SoC and we are in the process of transitioning our firmware from the development kit to the custom board. Our firmware...
Hello,
I am trying to run the system_off sample project to measure some low power currents. The sleep works as expected but once it reaches:
It does not go into deep...
If I wan to use the nRF52 as a Radio and not support any protocols.
I am looking to use this as a base band waveform processor and transverting down below 1Ghz.
What is...
I'm attempting to create firmware using nRF Connect SDK. Thoroughly studied these guides:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started...
I'm referring to nRF5 SDK 17.0.2. In 'external/freertos/config/FreeRTOSConfig.h', the value 'configLIBRARY_LOWEST_INTERRUPT_PRIORITY' is set to 0xf, but the nRF51/52 only...
Hello! I'm trying to use this low power UART sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/peripheral/lpuart/README.html I have a problem...
I want to add compiler flags to my build configuration i.e _DEBUG, etc
My understanding is that a build is done by build task
nRF Connect extension allows to create a...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard I add uart implementation from following...
