Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hello,
We observed that the BLE-Mesh provision logs are happening in FCBs of NV Flash, For my application i need them to be logged on RAM. Kindly suggest how I can achieve...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
