I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
SDK: NCS 2.0.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF5340
IDE: VS Code
Hi Everyone,
I am porting an existing project based...
Hello All,
We are intending to start a new project using nRF52840 SOC, for the same i decided to work with nRF connect SDK as it is recommended by nordic,
I am new to...
When connecting to AWS IOT the Asset Tracker V2 uses MQTT to AWS-IOT. This is TLS 1.2 from what I understand. We are using the 1.8 skd / 1.3.1 modem firmware.
We have...
Hi everyone
We have developed a smartwatch with a nrf9160 chip. We have used nrf Connect SDK 1.2 for the development process.
Now we want to migrate our project to nrf...
Hello there,
I am using the peripheral/radio/transmitter and receiver example in SDK17
But I am only able to transmit 2 bytes. I want to transmit like 8 or 9 bytes...
Hi,
I am testing FOTA function using sample "http_update/application_update" on NRF9160DK.
But found that the system boot stuck at
I had tested this sample with...
HI
I am using this sequence functions in my main loop for low current consumption
__SEV(); __WFE(); __WFE();
normally I have 13mA in my application when I am using...
nrf5-sdk v16.0.0
If you use the nrf_ble_scan module to try and connect to a peripheral that emits both connectable and non-connectable advertising packets, the module does...
Hello !
From PS it is not always clear what RADIO registers/fields are relevant for Ieee802154_250Kbit radio mode and must be initialized.
For example CRCINC ?
On "Figure...
Hi team,
I'm making BT low power keyboard using nRF52832 DV kit and with Zephyr RTOS. For this which IDE is best OR comfortable?
But I'm not getting example code if anyone...
I am programming an external device with the same code loaded onto the nRF5 DK. The sample works on the DK, It broadcasts and I can connect. However, when I program an external...
Hello. During development with the nrf52832 on the nRF52DK I've encountered a problem regarding the flash operations. When I try to perform a sd_flash_write operation, but...
Hello,
Our board consists of an STM32 microcontroller as the main core and an nRF52 as the BLE module.
In fact, we have older products on the market that support DFU...
Following up on https://devzone.nordicsemi.com/f/nordic-q-a/86119/some-zb_zcl_cluster_id_diagnostics-zigbee-attributes-do-not-return-values
It looks like this was fixed...
