The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
nRF Connect for Desktop 3.11.1, Programmer v.3.0.0.
Message showing with Jlink I am using and device connected:
13:58:12.602 Using nrf-device-lib-js version: 0.4.11...
We have developed a prototype board based on the Thingy91 which contains both the nRF9160 and nRF52840 and many of the same connections.
However, after a few successful...
Hello,
Now I am trying to merge usbd_ble_uart and ble_uart_c, I have found some example here.I am using nRF52840 DK , nRF52840 dongle and SDK 17.1.0.
I tried https://devzone...
Morning Everyone,
We use raspberry pis as part of our test equipment. The final stage of our CI/CD pipeline downloads the build dfu packages to a Pi and then does an OTA...
Hi,
I try to run SDK17.1 examples/dfu/secure_bootloader/pca10040_uart_debug.
Only UART example does not have softdevice.
I build and run that example on SES on M1...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Hi Sir/Miss,
I encounter a problem which is in programmer software.
When I open software and connect to nRF52840 DK. Right flash size window will display some animation...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Hi there,
I'm currently using SDK 17.1.0 with the NRF52832 Development Board. This is pretty new to me, but the examples helped me get an application going pretty quickly...
I'm using a nrf52840dongle board with the prj_no_dfu.conf configuration with the following additions:
CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n CONFIG_CHIP_LIB_SHELL=y CONFIG_LOG...
Dear Nordic Engineers
I install nrf command line 10.1.6.0 in my office PC.There was a problem after the installation complate.
I input "nrfjprog" in powerShell ,it's normal...
