Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi there,
I am trying to enable the Read Back Protection in the software itself to avoid the FLASH, RAM etc. from being read with a debugger after being flashed for production...
Hello, I'd like to check what is the typical distance using 0 dBm tx power using Nrf52840?
I am using this BLE module based on Nordic, and it seems to work ONLY 2-3m far...
Hello
I am getting started with Nordic devices.
I recently bought a Thingy:91 and followed a tutorial to load the Asset Tracker application on to the device – this...
Dear,
We have been using QSPI external flash (MX25R64 installed at nrf5340 DK board) to write data. Particularly, when we ran flash_area_erase function ( located at zephyr...
Hello All,
How can I get my nRF52840's MAC address in Zephyr? Actually, I want to append the last 4 characters of the MAC address in CONFIG_BT_DEVICE_NAME.
So, when I...
Hello, we are developing a zephyr application on top of nrf52 soc. We can use the built-in zephyr drivers for most modules (ex: I2C, UART, nvm, etc.); however, for some modules...
I am really new at working with Bluetooth and the various protocols contained within.
I am using SDK 17.0 and drivers 2.7. I am working on a DK-52 board.
I am working...
The TWIM peripheral allows you to tx multiple buffers back-to-back like this:
- Set buffer 1 in TXD.PTR, TXD.AMOUNT - Trigger TASKS_STARTTX - Wait for EVENTS_TXSTARTED ...
Hi,
For testing purposes, I need a copy of the spec that the Nordic UART BLE service adheres to. Ex. minimum capabilities, mandatory functionality and attributes, etc. ...
Hello,
I tried enabling the Zigbee shell, through RTT, in my application and when that failed I built and burned the nrf/samples/zigbee instead, slightly modded to get rid...
Hi All. My task is simple. I want to implement LE secure connections on DFU. I have seen the ble_gls example. It has a passkey for bonding, I am looking into that too. I ran...
I have a repository that is intended to be used by other repositories via ZEPHYR_EXTRA_MODULES. This seems to be working fine. However, now I'm trying to add some code to...
I am evaluating a front end module by skyworks 66111 output power is ~14dBm. The FEM requires that logic dictate when to transmit and when to receive. When CRX, pin 17, is...
HI
we have developed our custom board using nrf5340. We are using NCS v1.7.1 for application development. I can't able to flash the HCI_rpmsg application to the network...
