I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v5.0.0_src) and some other sensors which drivers are written by using nRF5_SDK_17.0.2. my device is battery operated...
In nRF_SDK_for _Tread_and_Zigbee, we used to set autocommissioning as false in the "thread_configuration_t" configuration and then start joined so that my thread node used...
The examples include checking the return code from various FDS calls immediately after the call.
Only some errors can be detected at the time of the call (for example NULL...
Hi,
I have created a vendor model for my application. When sending a message of 32bit it's working fine, but when I am changing the message length to 64bit by doing necessary...
Hello,
I am using a modifed Secure bootloader example in my NRF52840. I would like to show the user an update progress bar on the device screen while loading BLE DFU update...
Hello!
I am facing some strange behaviour using nordics dfu update service on android.
Somtimes after starting the dfu upload the app is not able to connect to the dfu...
Hi,
How to get this done using TWI this temperature sensor's I2C to write 16 bit register, it is sending start after device address then data. I tried as below, but it will...
Hi, I want to be able to send 1bit of data with as low latency as possible, what is the best way of doing this? Can i in some way directly control the low level of the radio...
Hi All,
i am using the below link to flash the bootloader
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/device-firmware-update-dfu-with...
Hello,
I am using Eclips & ARM tool chain for project with BLE functionality. I tried to import this code in Segger embedded IDE but it did not worked. This project is old...
Hello,
I built peripheral_hr_coded sample and looking into the partition manager report (I trucated the output):
What are the s0_pad and s1_pad?
What are the EMPTY_0...
Hello,
I am developing a FreeRTOS project that uses nRF5340 MCU. For the inter processor communication I would like to make use of the RTOS-agnostic RPC library (sdk-nrfxlib...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.7.1
Zephyr version: 2.6.99-ncs1-1 (commit...
Hi:
I have a BLE HID remote control that needs to be connected to the HID central(nRF52832).My SDK is NCS v1.8.0.
When I try to connect with the HID remote I get the log...
